Files
tpms-schrader-eg53ma4-sim/docs/SETUP.md
T
czcionka e183d23950
check / check-without-hardware (push) Successful in 6m45s
Docs and code: translate Polish comments, messages and documentation to English
- README, CHANGELOG, RELEASE_NOTES, THIRD_PARTY_NOTICES and docs/*.md
  translated to English; cross-markdown anchors updated
- C/C++/Python/shell comments and user-facing messages translated
- identifiers, protocol names, commands and literals unchanged
- native tests re-verified: 24/24 PASS; tpms_frame.py self-test PASS
2026-10-30 18:01:32 +00:00

4.3 KiB
Raw Blame History

Configuration and startup

Before you start

  1. Verify compatibility of the specific car (VIN, sensor markings, diagnostics, or reception). Do not rely solely on a number from a listing.
  2. Assemble the prototype per HARDWARE.md, flash the firmware, and open a 115200 UART.
  3. Type stay 300. info shows the active configuration, not just the saved one.
  4. Work on a parked car. The synthetic 260 kPa does not describe the real tyres.

Wheels: 1=FL front left, 2=FR front right, 3=RR rear right, 4=RL rear left. Configuration commands save to NVS automatically and verify the read back. An NVS error must be resolved before further testing, not ignored.

Path A — Clone IDs (preferred)

Use it when the original IDs were read earlier and the car still knows them.

  1. Write down four IDs as six-digit hex.

  2. Enter in turn (replace the example values with your own):

    id 1 2FC871
    id 2 2EAAF9
    id 3 3495AC
    id 4 2FC780
    pressure all 260
    info
    
  3. Check in info that all IDs and wheel assignments are correct. A duplicate, 000000, FFFFFF, or a value beyond 24 bits will be rejected.

  4. Optionally, send forces a cycle of all wheels. In NORMAL the device does it automatically as well; after a restart the configuration remains.

  5. Confirm reception externally. Known IDs may eliminate learning, but we do not promise that for every ECU state.

Do not use the example IDs in a vehicle if they may coincide with another device nearby.

Path B — New IDs + LEARN

Preparation

  1. ids new generates four unique IDs. You can use four id commands instead.
  2. info — write the IDs down on paper.
  3. Read the learning procedure for the specific model/equipment version. This document does not guess menus, pedal sequences, or the receiver location.
  4. Start the learning procedure in the car according to its service instructions.

Learning from the console

  1. mode learn — starts at FL; only FL transmits every 2 s.
  2. send — immediate FL burst, without changing the wheel.
  3. After completing the step for FL: next — FR; the LED shows 2 blinks.
  4. Repeat send, then next — RR, then next — RL.
  5. After the last next the device returns to NORMAL. The order is always FL → FR → RR → RL.
  6. Finish the car procedure according to its instructions and check the diagnostic readout.

Learning with one button

  • enter: hold ≥1.5 s;
  • short press: next wheel and an immediate burst;
  • force without changing the wheel: console send;
  • exit before the end: hold ≥1.5 s again or mode normal.

A 60 s timeout per wheel aborts LEARN to NORMAL; the whole session limit is 15 min. This is not an automatic learning success — you have to start again from the right wheel.

SINGLE / diagnostics

mode single 2 transmits only FR every 2 s. send forces FR, next moves on. mode normal ends it; the automatic limit is 5 min. The mode does not save the wheel selection in NVS and starts safely in NORMAL after a power loss.

Other settings

Command Range / effect
pressure all 260 0–637.5 kPa, P byte step ≈ 2.73 kPa (calibrated per the car, PROTOCOL.md)
temp all 23 −40…85 °C; °F in the frame
interval normal 30 interval without ACC, 5–86400 s
interval ignition 30 with hardware ACC active
interval parking 120 without active ACC
rf freq 433.92 433.05–434.79 MHz; changes require justification
rf power -10 −30, −20, −15, −10, −6, 0, 5 dBm
rf burst 3 1–8 frames per wheel
rf gap 50 20–500 ms between frames
flags 4C900070 experiment; bit meanings are unknown
factory YES erases your configuration and restores defaults

Schedule parameters are experimental. Power starts at −10 dBm; increase it only after a measurement and with the regulations in mind. Low emulator supply sets no sensor flag.

After a restart or brownout

The firmware reads NVS again. A correct version/CRC and ranges are required. A damaged or incompatible entry produces a message and a return to defaults, rather than transmitting a partly corrupted configuration. Every deep sleep has an alarm; there is no PARKING_SHUTDOWN mode that could leave the car without transmission until a manual wake.