This repository has been archived on 2026-11-06. You can view files and clone it. You cannot open issues or pull requests or push a commit.
Files
hassble-config/templates.yaml
T
eiggerandClaude Sonnet 5 a1a00b7636 fix(obd): replace additive odometer offset with a proportional one
offset_value -1436.5 fails a basic sanity check: applied to a hypothetical
new car reading 0 km on the engine counter, it would report a -1436.5 km
dash reading. An additive constant is only physically justified by a
one-time reset event, and the sign is wrong for that anyway — a reset
counter would read lower than the dash, not 0.73% higher.

A proportional error fits the actual mechanism. This DPF-service counter
converts wheel-speed pulses to distance with its own calibration constant,
separate from the cluster's regulated one, so it drifts from the true
distance in proportion to distance travelled, not by a fixed amount. That
model passes through the origin: a new car reads 0 km on both.

Replace scale 0.001 + offset_value -1436.5 with scale 0.000992723 (the ratio
195958/197394.5) on all three DPF-block sensors, not just the two the
constant version touched — a proportional correction must be applied
uniformly for odometer = odometer_at_last_dpf_regen + distance_since_dpf_regen
to still hold, unlike an additive one which happened to cancel out either way.

Add odometer_ext_session as a live retest of the cluster's own 22 B002.
Its earlier 7F 22 22 carried NRC 0x22 (conditionsNotCorrect), which per
ISO 14229-1 means the identifier exists but the ECU's current state refuses
it — unlike NRC 0x11/0x31, which would mean it does not exist at all. Send
a diagnostic session control (10 03) ahead of the read and watch the log: a
positive response there would give the dash value directly, replacing every
calibration assumption above with a value that needs none.

Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
2026-07-30 21:55:10 +09:00

390 lines
16 KiB
YAML

# Device templates for HassBle app → Sensors tab → Import template
# Loaded from repo root as templates.yaml (same branch as config.yaml)
templates:
- id: jaalee_jht
name: "Jaalee JHT"
description: "Temperature / humidity / battery (iBeacon, Apple manufacturer 76)"
device:
id: jaalee_jht
name: "Jaalee JHT"
source: advertisement
instance_mode: mac
match:
manufacturer_id: 76
manufacturer_min_length: 24
manufacturer_hex_prefix: "0215"
sensors:
- key: temperature
device_class: temperature
unit: "°C"
state_class: measurement
accuracy_decimals: 2
source_field: manufacturer_data
decode: { offset: 18, length: 2, type: uint16, endian: big, scale: 0.002670288, offset_value: -45 }
- key: humidity
device_class: humidity
unit: "%"
state_class: measurement
accuracy_decimals: 2
source_field: manufacturer_data
decode: { offset: 20, length: 2, type: uint16, endian: big, scale: 0.001524504 }
- key: battery
device_class: battery
unit: "%"
state_class: measurement
source_field: manufacturer_data
decode: { offset: 23, length: 1, type: uint8 }
- id: parking_beacon
name: "Parking Beacon"
description: "Shared parking beacon (manufacturer 861 / 0x035D)"
device:
id: parking_beacon
name: "Parking Beacon"
source: advertisement
instance_mode: shared
match:
manufacturer_id: 861
sensors:
- key: parking_time
device_class: timestamp
icon: mdi:clock-time-four-outline
source_field: manufacturer_data
length: 14
decode: { offset: 7, length: 4, type: timestamp }
- key: parking_floor
icon: mdi:layers-outline
source_field: manufacturer_data
length: 14
accuracy_decimals: 0
decode: { offset: 11, length: 1, type: uint8, scale: -1, offset_value: 256 }
- key: parking_location
platform: text_sensor
icon: mdi:map-marker-outline
source_field: manufacturer_data
length: 14
decode: { offset: 12, length: 2, type: string }
- id: obd_standard
name: "OBD-II (standard PIDs)"
description: "RPM, speed, coolant, fuel — bind ELM327 adapter in app"
device:
id: obd_vehicle
name: "OBD Vehicle"
source: obd
obd:
service_uuid: "FFF0"
tx_char_uuid: "FFF2"
rx_char_uuid: "FFF1"
tx_delay: 50ms
init_commands: []
sensors:
- { key: rpm, preset: rpm, update_interval: 1s }
- { key: speed, preset: speed, update_interval: 1s }
- { key: coolant_temp, preset: coolant_temp, update_interval: 10s }
- { key: fuel_level, preset: fuel_level, update_interval: 30s }
- id: obd_gm_extended
name: "OBD-II + GM extensions"
description: "Standard PIDs plus GM mode-22 sensors (ATSP6 init)"
device:
id: car_obd
name: "Vehicle OBD"
source: obd
obd:
service_uuid: "18F0"
tx_char_uuid: "2AF1"
rx_char_uuid: "2AF0"
tx_delay: 50ms
init_commands: ["ATSP6"]
sensors:
- { key: rpm, preset: rpm, update_interval: 1s }
- { key: speed, preset: speed, update_interval: 1s }
- { key: coolant_temp, preset: coolant_temp, update_interval: 10s }
- key: fuel_level
preset: fuel_level
update_interval: 30s
publish: { deadband: 0.5, min_interval: 60s }
- { key: gear, preset: gm_current_gear, update_interval: 1s }
- { key: prnd, preset: gm_prnd_status_alt, update_interval: 1s }
- { key: oil_pressure, preset: gm_oil_pressure, update_interval: 2s }
- { key: trans_temp, preset: gm_trans_temp, update_interval: 10s }
- id: obd_hyundai_kia
name: "OBD-II + 현대/기아 계기판"
description: "RPM, 속도, 총 주행거리, 연료잔량(L), 계기판 전압 — 계기판 7C6 / 22B002"
device:
id: car_obd_hk
name: "Hyundai/Kia OBD"
source: obd
obd:
service_uuid: "18F0"
tx_char_uuid: "2AF1"
rx_char_uuid: "2AF0"
tx_delay: 50ms
init_commands: ["ATSP6"]
# default_commands 생략 — 아래 ATSH7C6 센서가 있으므로 앱이 ATSH7DF로 자동 복원
sensors:
- { key: rpm, preset: rpm, update_interval: 1s }
- { key: speed, preset: speed, update_interval: 1s }
# 계기판(CLU) UDS. 요청 7C6 → 응답 7CE. 한 응답에 주행거리·연료·전압이 함께 온다.
# 응답: 62 B0 02 [a][b][c][d][e][f][g][h][i][j][k][l]…
# (a = 62B002 에코 바로 다음 바이트)
# e → 연료잔량 e*0.5 L
# f → 계기판 전압 f/12.8 = f*0.078125 V
# g:h:i → 총 주행거리 24bit km
# j:k:l → 위와 같은 주행거리의 mile 값 (북미 사양 계기판)
# 출처: OBDb(obdb.community)에서 현대·기아 11개 차종이 동일한 바이트 배치로 확인.
# awesomeit Torque 플러그인(35개 차종)·Elantra CN7 PID 목록과도 일치.
# 2013년식 이후에서 널리 동작하며, 미지원 차는 NO DATA를 반환한다.
#
# 예외: 엑센트(RB)는 계기판이 이 DID를 열지 않는다. 2013/2015/2019 실차 캡처에서
# unsupported로 확인됐고 (2018년식만 예외), 요청하면 7F 22 22를 돌려준다.
# 엑센트는 아래 obd_hyundai_accent_rb_diesel 템플릿을 쓸 것.
- key: odometer
mode: "22"
pid: "B002"
pre_commands: ["ATSH7C6"]
formula: "g*65536+h*256+i"
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 0
icon: mdi:counter
update_interval: 60s
- key: fuel_level
mode: "22"
pid: "B002"
pre_commands: ["ATSH7C6"]
formula: "e*0.5"
unit: "L"
state_class: measurement
accuracy_decimals: 1
icon: mdi:gas-station
update_interval: 30s
publish: { deadband: 0.5, min_interval: 60s }
- key: cluster_voltage
mode: "22"
pid: "B002"
pre_commands: ["ATSH7C6"]
formula: "f*0.078125"
unit: "V"
device_class: voltage
state_class: measurement
accuracy_decimals: 2
entity_category: diagnostic
update_interval: 60s
- id: obd_hyundai_accent_rb_diesel
name: "OBD-II 엑센트(RB) 디젤"
description: "RPM, 속도, 연료 %, 흡기온도, 대기압 + 총주행거리 프로브 — 엑센트 RB 1.6 TCI-U2"
device:
id: car_obd_accent
name: "Accent RB Diesel"
source: obd
obd:
service_uuid: "18F0"
tx_char_uuid: "2AF1"
rx_char_uuid: "2AF0"
tx_delay: 50ms
init_commands: ["ATSP6"]
# 아래 ATSH7E0 센서가 있으므로 표준 센서 앞에 ATSH7DF가 자동 삽입된다
sensors:
- { key: rpm, preset: rpm, update_interval: 1s }
- { key: speed, preset: speed, update_interval: 1s }
# 연료량은 이 차에서 읽을 방법이 없다. 표준 01 2F는 실차에서 NO DATA를
# 돌려주고(OBDb 캡처는 북미 가솔린 기준이라 디젤에는 맞지 않았다),
# 계기판 22B002도 7F 22 22로 거부한다.
# awesomeit 엑센트RB 2013 D 1.6 TCI-U2 프로필에서 확인된 값들
- key: intake_temp
mode: "21"
pid: "01"
pre_commands: ["ATSH7E0"]
formula: "k*0.980392-50"
unit: "°C"
device_class: temperature
state_class: measurement
accuracy_decimals: 1
update_interval: 10s
- key: barometric_pressure
mode: "21"
pid: "01"
pre_commands: ["ATSH7E0"]
formula: "j*1.372549"
unit: "kPa"
device_class: pressure
state_class: measurement
accuracy_decimals: 1
update_interval: 30s
# ── 총주행거리 (엔진 ECU의 DPF 블록에 같이 실려 온다) ──────────────
# 엑센트 RB는 계기판(7C6 / 22B002)이 주행거리를 직접 내주지 않는다 —
# 요청하면 7F 22 22. 그래서 대안으로 엔진 ECU의 21 03 블록을 쓴다
# (OBDb 메이커 공용 HYUNDAI_ODO_V2):
# byte 49~52 마지막 DPF 재생 시점의 주행거리 /1000 km
# byte 53~56 재생 이후 달린 거리 /1000 km
# byte 57~60 총주행거리 /1000 km ← 목표
# 셋은 서로 다른 필드다. awesomeit이 "DPF 주행거리"로 부르는 건 byte 53(재생 후 거리).
#
# 응답이 byte 57까지 도착하지 않으면 decode가 null을 돌려주고 아무것도
# 발행되지 않는다 — 미지원 차에서 엉뚱한 값이 올라오지 않는다.
#
# 보정: 2026-07-30 실측에서 이 ECU 카운터가 계기판(195958 km)보다
# 0.7331% 높게(197394.5 km) 나왔다. 처음엔 상수(offset_value)로 보정했으나
# 신차(카운터=0)에서 dash=-1436.5km 가 나오는 게 되어 성립할 수 없다.
# 배율(scale) 보정은 원점을 지나므로(카운터=0 → dash=0) 물리적으로 맞다 —
# 이 카운터는 계기판과 별개 환산계수로 바퀴속도 펄스를 거리로 누적하는
# 서비스용 값이라, 오차가 주행거리에 비례해 벌어지는 게 정상이다.
# 세 필드가 odometer = at_regen + since_regen 항등식을 만족하려면
# 셋 다 같은 배율을 써야 한다 (상수 보정과 달리 since_regen도 예외 없음).
#
# 측정이 한 점뿐이라 배율만 가정했고 절편은 0으로 뒀다. 100km 이상
# 주행 후 재확인해 두 점으로 완전한 affine 식(scale·offset_value 둘 다)을
# 풀 것 — 아래 odometer_ext_session 이 계기판 값을 직접 준다면 이 보정
# 자체가 필요 없어지므로 그쪽을 먼저 확인한다.
- key: odometer
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.000992723 }
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 1
icon: mdi:counter
update_interval: 60s
# 검산용: 재생시점 주행거리 + 재생후 거리 = 총주행거리.
# 셋 다 같은 카운터를 공유하므로 같은 배율을 적용해야 항등식이 유지된다.
- key: odometer_at_last_dpf_regen
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.000992723 }
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 1
entity_category: diagnostic
update_interval: 60s
- key: distance_since_dpf_regen
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
decode: { offset: 53, length: 4, type: uint32, endian: big, scale: 0.000992723 }
unit: "km"
device_class: distance
state_class: measurement
accuracy_decimals: 1
entity_category: diagnostic
update_interval: 60s
# ── 계기판 오도미터 재시도: 확장 진단 세션 ─────────────────────────
# 위 odometer 는 어디까지나 대체 경로(추정 보정)다. 진짜 계기판 값을
# 직접 받을 가능성이 아직 남아 있다 — 7F 22 22 의 NRC 22(conditionsNotCorrect)는
# UDS 표준상 "그 DID는 존재하는데 지금 조건에서 거부"라는 뜻이다.
# DID 자체가 없다는 NRC 11(serviceNotSupported)·31(requestOutOfRange)이 아니었다.
# 흔한 원인은 확장 진단 세션(10 03) 미진입이다. 요청 순서에 세션 진입을
# 끼워 넣고 재시도한다. 세션 진입 응답(1003) 자체는 로그에 안 남지만
# (pre_commands 응답은 기록되지 않음), 뒤따르는 22B002 응답은 그대로 남는다.
# raw=62B002… → 성공. formula 는 OBDb 배치(g:h:i = byte 6~8, 24bit) 그대로
# 써서 계기판 값이 보정 없이 직접 나온다
# negative response → 여전히 거부. NRC 가 바뀌었는지 확인 (22 그대로면
# 엔진 구동중이라 막힌 것일 수 있음 — 시동 끄고 재시도)
- key: odometer_ext_session
mode: "22"
pid: "B002"
pre_commands: ["ATSH7C6", "1003"]
formula: "g*65536+h*256+i"
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 0
entity_category: diagnostic
update_interval: 60s
# 계기판(22B002)·표준(01A6)·변속기(21A0) 오프셋 0~15 스캔은 195958km와
# 일치하는 값을 찾지 못해 제거했다. 계기판은 애초에 22B002 자체를
# 7F 22 22로 거부하므로 다른 DID를 더 뒤져볼 이유가 약하고, 표준 01A6은
# mode 01 지원 목록에 없어 예상대로였다. 위 offset_value 보정을 계속 쓴다.
# ── 변속기(TCU) 21A0 @ 7E1 ────────────────────────────────────────
# awesomeit 엑센트RB 2013 D 1.6 TCI-U2 프로필의 공식 그대로다.
# 오도미터 스캔과는 별개로, 이 블록 자체는 이 차에 존재하는 것으로 알려진
# 값이라 남겨둔다. 스캔은 offset 0~15만 봤고 이 값들은 13·20·21번째라
# 범위 안이었지만 195958과 다른 값(온도·기어)이라 스캔에서 걸러졌을 뿐,
# 응답 자체가 없었는지는 확인되지 않았다. 재임포트 후 값이 안 뜨면
# (NO DATA가 로그에 남으면) 이 3개도 지운다.
# N(byte 13) 미션오일온도, U(byte 20) 기어위치, V(byte 21) 기어단수
- key: trans_oil_temp
mode: "21"
pid: "A0"
pre_commands: ["ATSH7E1"]
formula: "n-40"
unit: "°C"
device_class: temperature
state_class: measurement
accuracy_decimals: 1
icon: mdi:oil-temperature
update_interval: 10s
- key: gear_position
mode: "21"
pid: "A0"
pre_commands: ["ATSH7E1"]
platform: text_sensor
icon: mdi:car-shift-pattern
decode:
offset: 20
length: 1
type: uint8
map:
"8": "D"
"9": "N"
"10": "R"
"11": "P"
"12": "Sport"
"16": "E Mode"
update_interval: 1s
- key: gear
mode: "21"
pid: "A0"
pre_commands: ["ATSH7E1"]
platform: text_sensor
icon: mdi:numeric
decode:
offset: 21
length: 1
type: uint8
map:
"0": "P/N"
"1": "1"
"2": "2"
"3": "3"
"4": "4"
"5": "5"
"6": "6"
"7": "7"
"8": "8"
update_interval: 1s
- id: gatt_meter_relay
name: "GATT power meter + relay"
description: "Notify characteristic + switch control example"
device:
id: custom_meter
name: "Custom BLE Meter"
source: gatt_notify
gatt:
service_uuid: "ffe0"
notify_char_uuid: "ffe1"
write_char_uuid: "ffe2"
sensors:
- key: power
unit: "W"
device_class: power
state_class: measurement
decode: { offset: 0, length: 2, type: uint16, endian: little }
controls:
- key: relay
type: switch
command: { on: "A10100", off: "A10000" }