Archived
Both earlier explanations for the missing gear sensors were wrong, and the response latencies in the logs rule them out. The 21 A0 reply is 61A0FFFF0000 in all 115 logged responses, and it is a finished reply rather than a first frame with the rest missing. Median round-trip is 92ms, against 79ms for the single-frame 010C and 76ms for 21 01, which returns 41 bytes across multiple frames. A stalled multi-frame would have to sit through the adapter's wait for the frames that never come before it prints a prompt, so it would be far slower, not the same speed. Multi-frame on 7E0 also completes normally in the very same session, so flow control is not implicated either. The ATFCSH7E1 setup added in the previous two commits was speculation and is removed. The 1.0.9 idle-wait change is not responsible either: sendCommand blocks on the prompt and the poll loop awaits it, so a later command cannot be written into the middle of a reply. The idle wait only covers gaps when no command is outstanding. So the ECU really does return four data bytes here, and awesomeit's byte 13, 20 and 21 cannot be reached from it. Whether that is because the profile describes a different specification, or because this TCU only fills the block under conditions not present while parked, is still open — every log so far was captured in park with the engine idling. Replace the three sensors with probes exposing bytes 0 through 3 directly, so shifting through P/R/N/D shows whether any of them move. If they do, that byte carries the gear; if FF FF 00 00 never changes, this TCU does not serve the block and the sensors should go for good. Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
393 lines
18 KiB
YAML
393 lines
18 KiB
YAML
# Device templates for HassBle app → Sensors tab → Import template
|
|
# Loaded from repo root as templates.yaml (same branch as config.yaml)
|
|
|
|
templates:
|
|
- id: jaalee_jht
|
|
name: "Jaalee JHT"
|
|
description: "Temperature / humidity / battery (iBeacon, Apple manufacturer 76)"
|
|
device:
|
|
id: jaalee_jht
|
|
name: "Jaalee JHT"
|
|
source: advertisement
|
|
instance_mode: mac
|
|
match:
|
|
manufacturer_id: 76
|
|
manufacturer_min_length: 24
|
|
manufacturer_hex_prefix: "0215"
|
|
sensors:
|
|
- key: temperature
|
|
device_class: temperature
|
|
unit: "°C"
|
|
state_class: measurement
|
|
accuracy_decimals: 2
|
|
source_field: manufacturer_data
|
|
decode: { offset: 18, length: 2, type: uint16, endian: big, scale: 0.002670288, offset_value: -45 }
|
|
- key: humidity
|
|
device_class: humidity
|
|
unit: "%"
|
|
state_class: measurement
|
|
accuracy_decimals: 2
|
|
source_field: manufacturer_data
|
|
decode: { offset: 20, length: 2, type: uint16, endian: big, scale: 0.001524504 }
|
|
- key: battery
|
|
device_class: battery
|
|
unit: "%"
|
|
state_class: measurement
|
|
source_field: manufacturer_data
|
|
decode: { offset: 23, length: 1, type: uint8 }
|
|
|
|
- id: parking_beacon
|
|
name: "Parking Beacon"
|
|
description: "Shared parking beacon (manufacturer 861 / 0x035D)"
|
|
device:
|
|
id: parking_beacon
|
|
name: "Parking Beacon"
|
|
source: advertisement
|
|
instance_mode: shared
|
|
match:
|
|
manufacturer_id: 861
|
|
sensors:
|
|
- key: parking_time
|
|
device_class: timestamp
|
|
icon: mdi:clock-time-four-outline
|
|
source_field: manufacturer_data
|
|
length: 14
|
|
decode: { offset: 7, length: 4, type: timestamp }
|
|
- key: parking_floor
|
|
icon: mdi:layers-outline
|
|
source_field: manufacturer_data
|
|
length: 14
|
|
accuracy_decimals: 0
|
|
decode: { offset: 11, length: 1, type: uint8, scale: -1, offset_value: 256 }
|
|
- key: parking_location
|
|
platform: text_sensor
|
|
icon: mdi:map-marker-outline
|
|
source_field: manufacturer_data
|
|
length: 14
|
|
decode: { offset: 12, length: 2, type: string }
|
|
|
|
- id: obd_standard
|
|
name: "OBD-II (standard PIDs)"
|
|
description: "RPM, speed, coolant, fuel — bind ELM327 adapter in app"
|
|
device:
|
|
id: obd_vehicle
|
|
name: "OBD Vehicle"
|
|
source: obd
|
|
obd:
|
|
service_uuid: "FFF0"
|
|
tx_char_uuid: "FFF2"
|
|
rx_char_uuid: "FFF1"
|
|
tx_delay: 50ms
|
|
init_commands: []
|
|
sensors:
|
|
- { key: rpm, preset: rpm, update_interval: 1s }
|
|
- { key: speed, preset: speed, update_interval: 1s }
|
|
- { key: coolant_temp, preset: coolant_temp, update_interval: 10s }
|
|
- { key: fuel_level, preset: fuel_level, update_interval: 60s }
|
|
|
|
- id: obd_gm_extended
|
|
name: "OBD-II + GM extensions"
|
|
description: "Standard PIDs plus GM mode-22 sensors (ATSP6 init)"
|
|
device:
|
|
id: car_obd
|
|
name: "Vehicle OBD"
|
|
source: obd
|
|
obd:
|
|
service_uuid: "18F0"
|
|
tx_char_uuid: "2AF1"
|
|
rx_char_uuid: "2AF0"
|
|
tx_delay: 50ms
|
|
init_commands: ["ATSP6"]
|
|
sensors:
|
|
- { key: rpm, preset: rpm, update_interval: 1s }
|
|
- { key: speed, preset: speed, update_interval: 1s }
|
|
- { key: coolant_temp, preset: coolant_temp, update_interval: 10s }
|
|
- key: fuel_level
|
|
preset: fuel_level
|
|
update_interval: 60s
|
|
publish: { deadband: 0.5, min_interval: 60s }
|
|
- { key: gear, preset: gm_current_gear, update_interval: 2s }
|
|
- { key: prnd, preset: gm_prnd_status_alt, update_interval: 2s }
|
|
- { key: oil_pressure, preset: gm_oil_pressure, update_interval: 5s }
|
|
- { key: trans_temp, preset: gm_trans_temp, update_interval: 10s }
|
|
|
|
- id: obd_hyundai_kia
|
|
name: "OBD-II + 현대/기아 계기판"
|
|
description: "RPM, 속도, 총 주행거리, 연료잔량(L), 계기판 전압 — 계기판 7C6 / 22B002"
|
|
device:
|
|
id: car_obd_hk
|
|
name: "Hyundai/Kia OBD"
|
|
source: obd
|
|
obd:
|
|
service_uuid: "18F0"
|
|
tx_char_uuid: "2AF1"
|
|
rx_char_uuid: "2AF0"
|
|
tx_delay: 50ms
|
|
init_commands: ["ATSP6"]
|
|
# default_commands 생략 — 아래 ATSH7C6 센서가 있으므로 앱이 ATSH7DF로 자동 복원
|
|
sensors:
|
|
- { key: rpm, preset: rpm, update_interval: 1s }
|
|
- { key: speed, preset: speed, update_interval: 1s }
|
|
# 계기판(CLU) UDS. 요청 7C6 → 응답 7CE. 한 응답에 주행거리·연료·전압이 함께 온다.
|
|
# 응답: 62 B0 02 [a][b][c][d][e][f][g][h][i][j][k][l]…
|
|
# (a = 62B002 에코 바로 다음 바이트)
|
|
# e → 연료잔량 e*0.5 L
|
|
# f → 계기판 전압 f/12.8 = f*0.078125 V
|
|
# g:h:i → 총 주행거리 24bit km
|
|
# j:k:l → 위와 같은 주행거리의 mile 값 (북미 사양 계기판)
|
|
# 출처: OBDb(obdb.community)에서 현대·기아 11개 차종이 동일한 바이트 배치로 확인.
|
|
# awesomeit Torque 플러그인(35개 차종)·Elantra CN7 PID 목록과도 일치.
|
|
# 2013년식 이후에서 널리 동작하며, 미지원 차는 NO DATA를 반환한다.
|
|
#
|
|
# 예외: 엑센트(RB)는 계기판이 이 DID를 열지 않는다. 2013/2015/2019 실차 캡처에서
|
|
# unsupported로 확인됐고 (2018년식만 예외), 요청하면 7F 22 22를 돌려준다.
|
|
# 엑센트는 아래 obd_hyundai_accent_rb_diesel 템플릿을 쓸 것.
|
|
- key: odometer
|
|
mode: "22"
|
|
pid: "B002"
|
|
pre_commands: ["ATSH7C6"]
|
|
formula: "g*65536+h*256+i"
|
|
unit: "km"
|
|
device_class: distance
|
|
state_class: total_increasing
|
|
accuracy_decimals: 0
|
|
icon: mdi:counter
|
|
update_interval: 60s
|
|
- key: fuel_level
|
|
mode: "22"
|
|
pid: "B002"
|
|
pre_commands: ["ATSH7C6"]
|
|
formula: "e*0.5"
|
|
unit: "L"
|
|
state_class: measurement
|
|
accuracy_decimals: 1
|
|
icon: mdi:gas-station
|
|
update_interval: 60s
|
|
publish: { deadband: 0.5, min_interval: 60s }
|
|
- key: cluster_voltage
|
|
mode: "22"
|
|
pid: "B002"
|
|
pre_commands: ["ATSH7C6"]
|
|
formula: "f*0.078125"
|
|
unit: "V"
|
|
device_class: voltage
|
|
state_class: measurement
|
|
accuracy_decimals: 2
|
|
entity_category: diagnostic
|
|
update_interval: 120s
|
|
|
|
- id: obd_hyundai_accent_rb_diesel
|
|
name: "OBD-II 엑센트(RB) 디젤"
|
|
description: "RPM, 속도, 연료 %, 흡기온도, 대기압 + 총주행거리 프로브 — 엑센트 RB 1.6 TCI-U2"
|
|
device:
|
|
id: car_obd_accent
|
|
name: "Accent RB Diesel"
|
|
source: obd
|
|
obd:
|
|
service_uuid: "18F0"
|
|
tx_char_uuid: "2AF1"
|
|
rx_char_uuid: "2AF0"
|
|
tx_delay: 50ms
|
|
init_commands: ["ATSP6"]
|
|
# 아래 ATSH7E0 센서가 있으므로 표준 센서 앞에 ATSH7DF가 자동 삽입된다
|
|
sensors:
|
|
- { key: rpm, preset: rpm, update_interval: 1s }
|
|
- { key: speed, preset: speed, update_interval: 1s }
|
|
# 연료량은 이 차에서 읽을 방법이 없다. 표준 01 2F는 실차에서 NO DATA를
|
|
# 돌려주고(OBDb 캡처는 북미 가솔린 기준이라 디젤에는 맞지 않았다),
|
|
# 계기판 22B002도 7F 22 22로 거부한다.
|
|
# awesomeit 엑센트RB 2013 D 1.6 TCI-U2 프로필에서 확인된 값들
|
|
- key: intake_temp
|
|
mode: "21"
|
|
pid: "01"
|
|
pre_commands: ["ATSH7E0"]
|
|
formula: "k*0.980392-50"
|
|
unit: "°C"
|
|
device_class: temperature
|
|
state_class: measurement
|
|
accuracy_decimals: 1
|
|
update_interval: 20s
|
|
- key: barometric_pressure
|
|
mode: "21"
|
|
pid: "01"
|
|
pre_commands: ["ATSH7E0"]
|
|
formula: "j*1.372549"
|
|
unit: "kPa"
|
|
device_class: pressure
|
|
state_class: measurement
|
|
accuracy_decimals: 1
|
|
update_interval: 60s
|
|
# ── 총주행거리 (엔진 ECU의 DPF 블록에 같이 실려 온다) ──────────────
|
|
# 엑센트 RB는 계기판(7C6 / 22B002)이 주행거리를 직접 내주지 않는다 —
|
|
# 요청하면 7F 22 22. 그래서 대안으로 엔진 ECU의 21 03 블록을 쓴다
|
|
# (OBDb 메이커 공용 HYUNDAI_ODO_V2):
|
|
# byte 49~52 마지막 DPF 재생 시점의 주행거리 /1000 km
|
|
# byte 53~56 재생 이후 달린 거리 /1000 km
|
|
# byte 57~60 총주행거리 /1000 km ← 목표
|
|
# 셋은 서로 다른 필드다. awesomeit이 "DPF 주행거리"로 부르는 건 byte 53(재생 후 거리).
|
|
#
|
|
# 응답이 byte 57까지 도착하지 않으면 decode가 null을 돌려주고 아무것도
|
|
# 발행되지 않는다 — 미지원 차에서 엉뚱한 값이 올라오지 않는다.
|
|
#
|
|
# 보정: 2026-07-30 실측에서 이 ECU 카운터가 계기판(195958 km)보다
|
|
# 0.7331% 높게(197394.5 km) 나왔다. 처음엔 상수(offset_value)로 보정했으나
|
|
# 신차(카운터=0)에서 dash=-1436.5km 가 나오는 게 되어 성립할 수 없다.
|
|
# 배율(scale) 보정은 원점을 지나므로(카운터=0 → dash=0) 물리적으로 맞다 —
|
|
# 이 카운터는 계기판과 별개 환산계수로 바퀴속도 펄스를 거리로 누적하는
|
|
# 서비스용 값이라, 오차가 주행거리에 비례해 벌어지는 게 정상이다.
|
|
# 세 필드가 odometer = at_regen + since_regen 항등식을 만족하려면
|
|
# 셋 다 같은 배율을 써야 한다 (상수 보정과 달리 since_regen도 예외 없음).
|
|
#
|
|
# 측정이 한 점뿐이라 배율만 가정했고 절편은 0으로 뒀다. 100km 이상
|
|
# 주행 후 재확인해 두 점으로 완전한 affine 식(scale·offset_value 둘 다)을
|
|
# 풀 것 — 아래 odometer_flow_control 이 계기판 값을 직접 준다면 이 보정
|
|
# 자체가 필요 없어지므로 그쪽을 먼저 확인한다.
|
|
# 오도미터는 분 단위로 갱신될 필요가 없고, 63바이트 멀티프레임이라 짧은
|
|
# PID보다 무겁다 — 주기를 늘리는 게 배터리에 가장 크게 도움되는 지점이다.
|
|
- key: odometer
|
|
mode: "21"
|
|
pid: "03"
|
|
pre_commands: ["ATSH7E0"]
|
|
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
|
unit: "km"
|
|
device_class: distance
|
|
state_class: total_increasing
|
|
accuracy_decimals: 1
|
|
icon: mdi:counter
|
|
update_interval: 300s
|
|
# 검산용: 재생시점 주행거리 + 재생후 거리 = 총주행거리.
|
|
# 셋 다 같은 카운터를 공유하므로 같은 배율을 적용해야 항등식이 유지된다.
|
|
- key: odometer_at_last_dpf_regen
|
|
mode: "21"
|
|
pid: "03"
|
|
pre_commands: ["ATSH7E0"]
|
|
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
|
unit: "km"
|
|
device_class: distance
|
|
state_class: total_increasing
|
|
accuracy_decimals: 1
|
|
entity_category: diagnostic
|
|
update_interval: 300s
|
|
- key: distance_since_dpf_regen
|
|
mode: "21"
|
|
pid: "03"
|
|
pre_commands: ["ATSH7E0"]
|
|
decode: { offset: 53, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
|
unit: "km"
|
|
device_class: distance
|
|
state_class: measurement
|
|
accuracy_decimals: 1
|
|
entity_category: diagnostic
|
|
update_interval: 300s
|
|
|
|
# ── 계기판 오도미터 재시도: 확장 진단 세션 ─────────────────────────
|
|
# 위 odometer 는 어디까지나 대체 경로(추정 보정)다. 진짜 계기판 값을
|
|
# 직접 받을 가능성이 아직 남아 있다 — 7F 22 22 의 NRC 22(conditionsNotCorrect)는
|
|
# UDS 표준상 "그 DID는 존재하는데 지금 조건에서 거부"라는 뜻이다.
|
|
# DID 자체가 없다는 NRC 11(serviceNotSupported)·31(requestOutOfRange)이 아니었다.
|
|
#
|
|
# meatpiHQ/wican-fw#478 에서 같은 헤더(7C6)·같은 PID(22B002)로 실제 성공한
|
|
# 사례 둘을 확인했다: 아이오닉 28kWh(WiCAN, pid_init "ATSH7C6;ATFCSH7C6")와
|
|
# 아이오닉5(canair, 세션 명령 없이 바로 조회). 둘 다 확장 세션(10 03) 없이
|
|
# 됐고, 공통점은 흐름제어(ATFCSH) 설정뿐이었다. 그래서 세션 대신 흐름제어를
|
|
# 먼저 시도한다 — 실제 성공 사례에 더 가깝다.
|
|
#
|
|
# 오도미터 위치도 세대별로 다르다: 아이오닉5·OBDb ICE 11개 차종은 byte
|
|
# 6~8(g,h,i)인데, 구형 아이오닉 28kWh는 byte 9~11(j,k,l)이었다
|
|
# (WiCAN이 ISO-TP PCI 바이트를 페이로드에 섞어 넣는 별도 버그가 있어,
|
|
# 그 이슈에서 공개한 보정표로 실제 위치를 역산한 값). 응답은 왔는데
|
|
# 195958과 안 맞으면 formula 를 "j*65536+k*256+l" 로 바꿔서 재시도할 것.
|
|
#
|
|
# pre_commands 자체의 응답(흐름제어 설정 OK/에러)은 로그에 안 남지만
|
|
# (해당 응답을 기다리는 센서가 없어 기록 경로를 안 탄다), 뒤따르는
|
|
# 22B002 응답은 그대로 남는다.
|
|
# raw=62B002… → 성공. 계기판 값이 보정 없이 직접 나온다
|
|
# negative response 그대로 → 흐름제어도 소용없음. 세션(10 03)으로 한 번 더
|
|
# 시도해볼 수는 있으나, 위 두 성공 사례 모두 세션 없이 됐다는 점에서
|
|
# 이 차는 DID 자체가 없을 가능성이 이전보다 높아졌다.
|
|
- key: odometer_flow_control
|
|
mode: "22"
|
|
pid: "B002"
|
|
pre_commands: ["ATSH7C6", "ATFCSH7C6", "ATFCSD300000", "ATFCSM1"]
|
|
formula: "g*65536+h*256+i"
|
|
unit: "km"
|
|
device_class: distance
|
|
state_class: total_increasing
|
|
accuracy_decimals: 0
|
|
entity_category: diagnostic
|
|
update_interval: 300s
|
|
|
|
# 계기판(22B002)·표준(01A6)·변속기(21A0) 오프셋 0~15 스캔은 195958km와
|
|
# 일치하는 값을 찾지 못해 제거했다. 계기판은 애초에 22B002 자체를
|
|
# 7F 22 22로 거부하므로 다른 DID를 더 뒤져볼 이유가 약하고, 표준 01A6은
|
|
# mode 01 지원 목록에 없어 예상대로였다. 위 offset_value 보정을 계속 쓴다.
|
|
|
|
# ── 변속기(TCU) 21 A0 @ 7E1 — 응답이 4바이트뿐이다 ────────────────
|
|
# 실측: 요청 116건, 응답 115건이 전부 61A0FFFF0000.
|
|
# 에코(61 A0)를 뺀 데이터는 FF FF 00 00 — 4바이트가 전부다.
|
|
#
|
|
# 잘린 멀티프레임이 아니라 완결된 응답이다. 응답 지연 중앙값이 92ms 로,
|
|
# 단일프레임 010C(79ms)·멀티프레임 2101(41바이트, 76ms)과 같은 수준이다.
|
|
# First Frame 만 오고 CF 가 끊긴 것이라면 ELM327 이 CF 를 기다리다
|
|
# 내부 타임아웃을 먹어야 하므로 지연이 훨씬 커진다. 그런 흔적이 없다.
|
|
# 흐름제어(ATFCSH) 문제도 아니다 — 같은 세션에서 7E0 멀티프레임은 정상이다.
|
|
#
|
|
# 따라서 awesomeit 프로필의 byte 13(미션오일온도)·20(기어위치)·21(기어단수)은
|
|
# 이 응답으로는 절대 닿지 않는다. 프로필이 다른 사양 기준이거나,
|
|
# 이 TCU 가 특정 조건에서만 전체 블록을 준다는 뜻이다.
|
|
#
|
|
# 아래는 실제로 오는 4바이트를 그대로 노출하는 프로브다.
|
|
# 주차(P)·엔진공회전 상태에서만 로그를 떴으므로, 주행 중이나 기어를 바꿀 때
|
|
# 값이 달라지는지 봐야 한다. 값이 움직이면 그 바이트가 기어 정보이고,
|
|
# FF FF 00 00 이 계속 고정이면 이 차 TCU 는 이 블록을 안 채우는 것이다.
|
|
- key: tcu_byte0
|
|
mode: "21"
|
|
pid: "A0"
|
|
pre_commands: ["ATSH7E1"]
|
|
decode: { offset: 0, length: 1, type: uint8 }
|
|
entity_category: diagnostic
|
|
update_interval: 2s
|
|
- key: tcu_byte1
|
|
mode: "21"
|
|
pid: "A0"
|
|
pre_commands: ["ATSH7E1"]
|
|
decode: { offset: 1, length: 1, type: uint8 }
|
|
entity_category: diagnostic
|
|
update_interval: 2s
|
|
- key: tcu_byte2
|
|
mode: "21"
|
|
pid: "A0"
|
|
pre_commands: ["ATSH7E1"]
|
|
decode: { offset: 2, length: 1, type: uint8 }
|
|
entity_category: diagnostic
|
|
update_interval: 2s
|
|
- key: tcu_byte3
|
|
mode: "21"
|
|
pid: "A0"
|
|
pre_commands: ["ATSH7E1"]
|
|
decode: { offset: 3, length: 1, type: uint8 }
|
|
entity_category: diagnostic
|
|
update_interval: 2s
|
|
|
|
- id: gatt_meter_relay
|
|
name: "GATT power meter + relay"
|
|
description: "Notify characteristic + switch control example"
|
|
device:
|
|
id: custom_meter
|
|
name: "Custom BLE Meter"
|
|
source: gatt_notify
|
|
gatt:
|
|
service_uuid: "ffe0"
|
|
notify_char_uuid: "ffe1"
|
|
write_char_uuid: "ffe2"
|
|
sensors:
|
|
- key: power
|
|
unit: "W"
|
|
device_class: power
|
|
state_class: measurement
|
|
decode: { offset: 0, length: 2, type: uint16, endian: little }
|
|
controls:
|
|
- key: relay
|
|
type: switch
|
|
command: { on: "A10100", off: "A10000" }
|