Archived
fix(obd): replace additive odometer offset with a proportional one
offset_value -1436.5 fails a basic sanity check: applied to a hypothetical new car reading 0 km on the engine counter, it would report a -1436.5 km dash reading. An additive constant is only physically justified by a one-time reset event, and the sign is wrong for that anyway — a reset counter would read lower than the dash, not 0.73% higher. A proportional error fits the actual mechanism. This DPF-service counter converts wheel-speed pulses to distance with its own calibration constant, separate from the cluster's regulated one, so it drifts from the true distance in proportion to distance travelled, not by a fixed amount. That model passes through the origin: a new car reads 0 km on both. Replace scale 0.001 + offset_value -1436.5 with scale 0.000992723 (the ratio 195958/197394.5) on all three DPF-block sensors, not just the two the constant version touched — a proportional correction must be applied uniformly for odometer = odometer_at_last_dpf_regen + distance_since_dpf_regen to still hold, unlike an additive one which happened to cancel out either way. Add odometer_ext_session as a live retest of the cluster's own 22 B002. Its earlier 7F 22 22 carried NRC 0x22 (conditionsNotCorrect), which per ISO 14229-1 means the identifier exists but the ECU's current state refuses it — unlike NRC 0x11/0x31, which would mean it does not exist at all. Send a diagnostic session control (10 03) ahead of the read and watch the log: a positive response there would give the dash value directly, replacing every calibration assumption above with a value that needs none. Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
This commit is contained in:
1 parent
d6fc16a875
commit
a1a00b7636
1 file changed
+44
-17
+44
-17
@@ -218,31 +218,35 @@ templates:
|
||||
accuracy_decimals: 1
|
||||
update_interval: 30s
|
||||
# ── 총주행거리 (엔진 ECU의 DPF 블록에 같이 실려 온다) ──────────────
|
||||
# 엑센트 RB는 계기판(7C6 / 22B002)이 주행거리를 열지 않는다 — 요청하면 7F 22 22.
|
||||
# 대신 엔진 ECU의 21 03 블록에 있다 (OBDb 메이커 공용 HYUNDAI_ODO_V2):
|
||||
# 엑센트 RB는 계기판(7C6 / 22B002)이 주행거리를 직접 내주지 않는다 —
|
||||
# 요청하면 7F 22 22. 그래서 대안으로 엔진 ECU의 21 03 블록을 쓴다
|
||||
# (OBDb 메이커 공용 HYUNDAI_ODO_V2):
|
||||
# byte 49~52 마지막 DPF 재생 시점의 주행거리 /1000 km
|
||||
# byte 53~56 재생 이후 달린 거리 /1000 km
|
||||
# byte 57~60 총주행거리 /1000 km ← 목표
|
||||
# 셋은 서로 다른 필드다. awesomeit이 "DPF 주행거리"로 부르는 건 byte 53(재생 후 거리).
|
||||
# 그 프로필이 같은 21 03에서 byte 53~55를 읽으므로, 이 차의 응답은 최소
|
||||
# byte 55까지 도착한다 — 목표는 두 바이트 뒤다.
|
||||
#
|
||||
# 응답이 byte 57까지 도착하지 않으면 decode가 null을 돌려주고 아무것도
|
||||
# 발행되지 않는다 — 미지원 차에서 엉뚱한 값이 올라오지 않는다.
|
||||
#
|
||||
# offset_value = -1436.5 는 계기판 대조 보정이다. 2026-07-30 실측에서
|
||||
# ECU 카운터 197394.5 km, 계기판 195958 km 로 0.733% 높게 나왔다.
|
||||
# 이 카운터는 DPF 서비스 주기용이라 법정 계기판 수치와 별개로 관리되고,
|
||||
# 속도 신호원이 달라 장기간에 걸쳐 벌어진다.
|
||||
# 측정이 한 번뿐이라 상수 오차인지 비례 오차인지 구분되지 않아 우선 상수로 뒀다.
|
||||
# 100km 이상 주행 후 재확인할 것:
|
||||
# 차이가 1436.5 그대로면 상수가 맞고, 1437.2 근처로 늘면 비례이므로
|
||||
# offset_value 를 빼고 scale 을 0.000992723 으로 바꾼다.
|
||||
# 보정: 2026-07-30 실측에서 이 ECU 카운터가 계기판(195958 km)보다
|
||||
# 0.7331% 높게(197394.5 km) 나왔다. 처음엔 상수(offset_value)로 보정했으나
|
||||
# 신차(카운터=0)에서 dash=-1436.5km 가 나오는 게 되어 성립할 수 없다.
|
||||
# 배율(scale) 보정은 원점을 지나므로(카운터=0 → dash=0) 물리적으로 맞다 —
|
||||
# 이 카운터는 계기판과 별개 환산계수로 바퀴속도 펄스를 거리로 누적하는
|
||||
# 서비스용 값이라, 오차가 주행거리에 비례해 벌어지는 게 정상이다.
|
||||
# 세 필드가 odometer = at_regen + since_regen 항등식을 만족하려면
|
||||
# 셋 다 같은 배율을 써야 한다 (상수 보정과 달리 since_regen도 예외 없음).
|
||||
#
|
||||
# 측정이 한 점뿐이라 배율만 가정했고 절편은 0으로 뒀다. 100km 이상
|
||||
# 주행 후 재확인해 두 점으로 완전한 affine 식(scale·offset_value 둘 다)을
|
||||
# 풀 것 — 아래 odometer_ext_session 이 계기판 값을 직접 준다면 이 보정
|
||||
# 자체가 필요 없어지므로 그쪽을 먼저 확인한다.
|
||||
- key: odometer
|
||||
mode: "21"
|
||||
pid: "03"
|
||||
pre_commands: ["ATSH7E0"]
|
||||
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.001, offset_value: -1436.5 }
|
||||
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
||||
unit: "km"
|
||||
device_class: distance
|
||||
state_class: total_increasing
|
||||
@@ -250,13 +254,12 @@ templates:
|
||||
icon: mdi:counter
|
||||
update_interval: 60s
|
||||
# 검산용: 재생시점 주행거리 + 재생후 거리 = 총주행거리.
|
||||
# 재생시점 값도 같은 ECU 카운터라 위와 같은 보정을 걸어야 이 관계가 유지된다.
|
||||
# 재생후 거리는 차분이라 편향이 없으므로 보정하지 않는다.
|
||||
# 셋 다 같은 카운터를 공유하므로 같은 배율을 적용해야 항등식이 유지된다.
|
||||
- key: odometer_at_last_dpf_regen
|
||||
mode: "21"
|
||||
pid: "03"
|
||||
pre_commands: ["ATSH7E0"]
|
||||
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.001, offset_value: -1436.5 }
|
||||
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
||||
unit: "km"
|
||||
device_class: distance
|
||||
state_class: total_increasing
|
||||
@@ -267,7 +270,7 @@ templates:
|
||||
mode: "21"
|
||||
pid: "03"
|
||||
pre_commands: ["ATSH7E0"]
|
||||
decode: { offset: 53, length: 4, type: uint32, endian: big, scale: 0.001 }
|
||||
decode: { offset: 53, length: 4, type: uint32, endian: big, scale: 0.000992723 }
|
||||
unit: "km"
|
||||
device_class: distance
|
||||
state_class: measurement
|
||||
@@ -275,6 +278,30 @@ templates:
|
||||
entity_category: diagnostic
|
||||
update_interval: 60s
|
||||
|
||||
# ── 계기판 오도미터 재시도: 확장 진단 세션 ─────────────────────────
|
||||
# 위 odometer 는 어디까지나 대체 경로(추정 보정)다. 진짜 계기판 값을
|
||||
# 직접 받을 가능성이 아직 남아 있다 — 7F 22 22 의 NRC 22(conditionsNotCorrect)는
|
||||
# UDS 표준상 "그 DID는 존재하는데 지금 조건에서 거부"라는 뜻이다.
|
||||
# DID 자체가 없다는 NRC 11(serviceNotSupported)·31(requestOutOfRange)이 아니었다.
|
||||
# 흔한 원인은 확장 진단 세션(10 03) 미진입이다. 요청 순서에 세션 진입을
|
||||
# 끼워 넣고 재시도한다. 세션 진입 응답(1003) 자체는 로그에 안 남지만
|
||||
# (pre_commands 응답은 기록되지 않음), 뒤따르는 22B002 응답은 그대로 남는다.
|
||||
# raw=62B002… → 성공. formula 는 OBDb 배치(g:h:i = byte 6~8, 24bit) 그대로
|
||||
# 써서 계기판 값이 보정 없이 직접 나온다
|
||||
# negative response → 여전히 거부. NRC 가 바뀌었는지 확인 (22 그대로면
|
||||
# 엔진 구동중이라 막힌 것일 수 있음 — 시동 끄고 재시도)
|
||||
- key: odometer_ext_session
|
||||
mode: "22"
|
||||
pid: "B002"
|
||||
pre_commands: ["ATSH7C6", "1003"]
|
||||
formula: "g*65536+h*256+i"
|
||||
unit: "km"
|
||||
device_class: distance
|
||||
state_class: total_increasing
|
||||
accuracy_decimals: 0
|
||||
entity_category: diagnostic
|
||||
update_interval: 60s
|
||||
|
||||
# 계기판(22B002)·표준(01A6)·변속기(21A0) 오프셋 0~15 스캔은 195958km와
|
||||
# 일치하는 값을 찾지 못해 제거했다. 계기판은 애초에 22B002 자체를
|
||||
# 7F 22 22로 거부하므로 다른 DID를 더 뒤져볼 이유가 약하고, 표준 01A6은
|
||||
|
||||
Reference in new issue
Block a user