- README, CHANGELOG, RELEASE_NOTES, THIRD_PARTY_NOTICES and docs/*.md translated to English; cross-markdown anchors updated - C/C++/Python/shell comments and user-facing messages translated - identifiers, protocol names, commands and literals unchanged - native tests re-verified: 24/24 PASS; tpms_frame.py self-test PASS
4.7 KiB
Energy and parking behaviour
Measurement status
No current measurements of the physical prototype have been performed. The numbers below are budget estimates, not validated results. The S2 Mini is not suitable for declaring µA consumption without measurement: the built-in regulator, LED, and auxiliary circuits add consumption. The LM317T itself loads the supply with a divider current of about 5 mA (R1 = 240 Ω) plus its own quiescent current, so a permanent supply needs a separate energy budget. The target supply from an ignition-switched cigarette-lighter socket removes this problem: with the ignition off the emulator draws no current at all.
Firmware schedule
- NORMAL after the RTC wake: initialisation, a burst of four wheels, exit of TX, and deep sleep. There is no 10-second console window after a plain wake.
- Micro-naps: sleep is split into pieces so that the LED blinks about every
2 s, also between transmissions (
NAP_PERIOD_MSinconfig.h). After a timer wake the device shows one visible blink and sleeps the rest of the period after boot time + window (NAP_AWAKE_MS). The button wakes immediately (EXT1) regardless of the micro-naps. - TX of frames remains on the interval (default 30 s): the sleep counter in
RTC memory counts the slept pieces since the last TX cycle;
intervaltakes effect on the next cycle. After a longer awake period (e.g.stay), the first piece is a full one. - Micro-naps raise consumption (a boot about every 2 s instead of one sleep per interval) — the numbers below describe the old model and require HIL measurement.
- After power-on, a button, or LF: a 10 s console window;
stay Nextends it. - LEARN: TX of one wheel every 2 s, without deep sleep, max 60 s per wheel/ 15 min per session.
- SINGLE: TX of one wheel every 2 s, without deep sleep, max 5 min.
- The CC1101 enters SPWD before sleep; CS is high, SCK/MOSI low, LED off.
- Every sleep has an RTC alarm.
PARKING_SHUTDOWNwas removed — the device cannot remain asleep until a purely manual wake. - ACC (optional in hardware) selects the ignition/parking interval. It is not needed as the only wake source, because the RTC always runs. If the whole assembly is powered only from an ignition-switched lighter socket or from ACC, then with ACC off there is no power, no RTC, and no transmission — and that is the target scenario.
Charge estimate for the default settings
One frame is 240 × 120 µs = 28.8 ms on air. For 4 wheels × 3 frames: 345.6 ms of transmission plus 8 × 50 ms gaps inside the bursts. On top of that come boot, configuration, SPI, and logging. For energy calculations you must measure the whole cycle, not just the OOK time.
An example model (to be replaced by measurement): if ESP32 activity is 1.0 s at 80 mA every 30 s, the ESP32 alone averages about 2.7 mA at 3.3 V. The CC1101, boot, and sleep current add further terms. With a 120 s interval the activity share falls about fourfold, but the constant Iq of the regulator and the dividers remains. These are not measured 2.7 mA nor a promise of consumption from a 12 V battery.
Measurement method required before "validated"
- The whole S2 Mini in sleep: a µA meter in series at the input, not through USB. Wait until TX ends and record the minimum/steady state and the board model.
- S2 Mini + LM317T: repeat the measurement on the protected VIN input and on the 3.3 V rail. Include the regulator divider current, TVS, the other dividers, and pull-ups.
- NORMAL cycle: a shunt + oscilloscope or a logger with sufficient bandwidth. Record boot, 12 frames, gaps, and entering sleep over at least 10 cycles.
- Average: integrate the charge for at least 15 min at 30 s and 120 s. State the conditions: voltage, temperature, PA, board and firmware version.
- LEARN/SINGLE: measure the continuous-awake current separately.
- ACC/brownout/crank: check restart, the return to transmission, and NVS integrity. Do not test on GPIO without confirmed input protection.
Conclusions allowed before measurement
- The interval, awake time, PA, and the whole board's Iq have the largest impact.
- A power-saving version requires measuring the whole S2 Mini and LM317T; with power only from an ignition-switched lighter socket the assembly draws no current after the ignition goes off, but then it also transmits no parking mode — which matches the assumption, because the car ECU does not listen then.
- We do not recommend an 18650 in the cabin, nor multi-year battery operation with an ESP32.
- The emulator's constant consumption must be accounted for during a long park; we do not give a "safe for the battery" time without measuring the whole car.