# Changelog ## Work in progress after 2.0.0-rc.1 - Micro-naps instead of one long sleep (`config.h`: `NAP_PERIOD_MS`): the LED blinks approximately every 2 s also between transmissions, and after every timer wake a blink is visible (`NAP_AWAKE_MS`). Sleep is the remainder of the period after boot time + window; TX of frames remains on the interval (sleep counter in RTC memory, `interval` takes effect on the next cycle). `power_deep_sleep` takes milliseconds. Previously, waking from the timer turned the LED off in the same `loop()` — the blink lasted a few ms and the wake-up was invisible. - Button: the board's BOOT button by default (`PIN_BUTTON = 0`, GPIO0) — EXT1 behaviour confirmed on hardware. An external button on GPIO3 is selected with `-DPIN_BUTTON=3`. Note: GPIO0 is a strapping pin (held at power-up/reset it starts the bootloader). Every button gesture opens a 10 s console window (per `POWER.md`) — the device does not fall asleep immediately after, e.g., leaving LEARN/SINGLE. LEARN/SINGLE still do not sleep (unchanged). - Calibration of the pressure field `P` against the car display: the rtl_433 scale (2.5 kPa/bit) is not confirmed (the captures have `P=0`), and the car showed 284 kPa for 260 kPa. The scaling correction `TPMS_PRESSURE_KPA100_PER_RAW` (273 = 2.73 kPa/bit; `P=95` for 260 kPa) was applied in the firmware, the Python model, and the `verify_rtl433.py` expectations. Confirmed on hardware: 260 kPa → 260 kPa on the car display. - Hardware–firmware integration audit (2026-10-28), consistency of ESP32-S2-MINI + CC1101 SMA + LM317T: - EXT1 wake: the RTC pulls for the button and LF are configured before deep sleep. A digital pull-up (`pinMode`) does not work with the RTC_PERIPH domain disabled (ESP-IDF documentation), so the wake pins floated and EXT1 could wake randomly. An external 10 kΩ is also recommended. - Console: number parsing rejects NaN and infinity (previously `pressure nan` / `rf freq nan` passed validation; NaN ended up in NVS as pressure, and `rf freq nan` blocked later writes). The parsing logic was extracted into the portable `parse` module with native tests. - Power: ADC divider R2 270 kΩ → 180 kΩ. The previous divider saturated the ADC (2.5 V full scale) already above about 11.8 V and did not measure the 12 V installation under a 12.6–14.4 V operating range. - `tools/package_release.sh`: the full `merge_bin` image uses `--flash-freq 80m` consistent with the `lolin_s2_mini` manifest; the previous `40m` overwrote the bootloader header (80 MHz) with a parameter that differed from the build. - `tools/tpms_frame.py`: temperature saturation to 0–255 consistent with the firmware (temperatures ≤ −19 °C corrupted the frame in the Python model). - Tests: the negative checksum case now inverts the whole Manchester cell (previously it exercised a Manchester violation instead of the sum); a new `test_parse` suite (ranges, NaN/inf); corrected the bit diagram in `PROTOCOL.md`. - Target hardware changed to ESP32-S2-MINI (ESP32-S2FN4R2, e.g. ARD-ESP32-S2-MINI, board `lolin_s2_mini`); updated the PlatformIO target, native USB CDC, SPI/button/ADC pinout, and built-in LED polarity (GPIO15, active HIGH). Supply ADC on GPIO1, optional LF on GPIO14. `btStop()` is compiled only on chips with Bluetooth — the ESP32-S2 has none. - CC1101 433 MHz SPI radio module with an SMA connector and antenna (ARD-CC1101-ANT). - External power through an adjustable LM317T (TO-220 metal, 1.25–37 V, 1.5 A): the correct ADJ–VOUT–IN pinout, TAB = VOUT, a 240/390 Ω divider giving about 3.28 V, capacitors, and protection and thermal requirements. - Target power from the car cigarette-lighter socket: a USB charger (variant A) or the LM317T (variant B). With an ignition-switched socket the emulator draws no current while parked; the lack of parking transmission is acceptable because the car ECU does not read TPMS with the ignition off. - ESP32-S2 release images use `esptool --chip esp32s2` and a bootloader at address `0x1000`; older images for ESP32-C3 and ESP32-WROOM are incompatible. ## 2.0.0-rc.1 — 2026-10-27 Release candidate without a physical CC1101 test and a car test. ### Added - Persistent NVS configuration with versioning, CRC32, range validation, unique IDs, factory reset, and safe defaults. - Console: Clone IDs, a new-ID generator, pressures/temperature, intervals, limited RF, LEARN/SINGLE, and diagnostics without recompilation. - Portable state machine with fake clock/radio, timeouts, and the FL→FR→RR→RL order. Restart, ACC, radio-failure, and `millis()` wrap tests. - Independent validation of four reference recordings and synthetic CU8 with the pinned rtl_433; negative checksum/Manchester/truncation tests. - `tools/check_all`, Dockerfile, Gitea Actions, image scripts, and SHA-256. - User, hardware, power, safety, and HIL documentation. ### Changed - Defaults of 260 kPa and −10 dBm, OOK only. The 30-byte Manchester encoder is preserved and passes independent decoding. - The CC1101 waits for `MARCSTATE=IDLE`, checks underflow and leftover bytes, instead of relying only on timing and `TXBYTES=0`. - A plain RTC wake does not open the console window; transmission and the return to sleep limit the estimated consumption. The console window remains open after user interaction. - Full build with `-Wall -Wextra -Werror`; cppcheck with zero defects. ### Removed / fixed - Removed the guessed `TPMS_FLAGS_LOWBAT_MASK` and the coupling between the emulator's low supply and the simulated sensor. The supply is only a local warning. - Removed FSK from the main flow: no evidence for the analysed profile. - Removed `PARKING_SHUTDOWN`; every deep sleep has an RTC alarm, so an ACC restart cannot leave the device permanently asleep. - The default, unvalidated LF input is disabled. Basic LEARN does not require the EL-50448. - Removed the recommendation of MCP1703 + 24 V TVS as automotive protection and the promises of multi-year battery operation. The 12 V supply has design requirements, not HIL. ### Audit iterations 1. **Initial state:** 7/7 native and build PASS, but configuration through recompilation, a monolithic state machine, lowbat, and power needed repair. Created `archive/pre-opencode`. 2. **Data model:** added NVS/CRC/validation and portable modes. The first test caught wrong test expectations for a pending tick and immediate TX; after correction, 20/20 native and the ESP32 build PASS. 3. **RF validation:** an audit of four recordings confirmed 16 repetitions and variable gaps. A single vector was replaced with the full script; 64/64 references, 3/3 synthetic, and 3/3 negative PASS. 4. **Energy:** a console window after every RTC wake was detected; it was limited to interaction. Consumption is still clearly marked as estimated. 5. **Static analysis:** cppcheck flagged memset-initialised float structs; replaced with value initialisation and reached 0 defects. ### Not physically verified CC1101 on an antenna/analyser, RTL-SDR with the prototype, consumption, brownout, ACC, a flash update, Clone IDs and LEARN with the specific Opel. No "validated" label.