fix(obd): calibrate the Accent odometer and drop what the car cannot read

Real readings from the car on 2026-07-30:

  odometer                   197394.5 km
  odometer at last regen     197055.5 km
  distance since regen           339.0 km
  dash                       195958   km

197055.5 + 339.0 = 197394.5 to the decimal, which confirms bytes 49, 53 and
57 are all decoded correctly. The ECU counter simply runs 1436.5 km — 0.733%
— above the cluster. It exists to time DPF service intervals, is fed by a
different speed source than the legal odometer, and drifts from it over a
vehicle's life.

Apply that as offset_value on the odometer, and on the odometer at last
regeneration since it reads the same counter and the cross-check only holds
if both move together. Distance since regeneration is a difference, carries
no bias, and stays as it is.

One reading cannot tell a constant error from a proportional one. A constant
is assumed for now and the comment records how to settle it: after 100 km or
more, a gap still at 1436.5 confirms the constant, while a gap near 1437.2
means it scales and offset_value should give way to scale 0.000992723.

Drop fuel_percent. Standard 01 2F answers NO DATA on this car — OBDb's Accent
capture that recorded it as supported is a North American petrol car — and
the cluster refuses 22 B002, so there is no route to fuel level here.

Drop probe_2103 now that the real sensors report, and give both DPF sensors a
state_class so Home Assistant stops warning that a unit is set without one.

Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
This commit is contained in:
eiggerandClaude Opus 5 committed 2026-07-30 13:09:14 +09:00
1 parent 0b368acd79
commit 286c6290c9
1 file changed
+19 -14
+19 -14
View File
@@ -193,9 +193,9 @@ templates:
sensors:
- { key: rpm, preset: rpm, update_interval: 1s }
- { key: speed, preset: speed, update_interval: 1s }
# 표준 연료 게이지(%). OBDb 엑센트 실차 캡처에서 2013~2019 전 연식
# 7E0 supported(012F:FLI)로 확인됨. 계기판 리터 값과 별개 경로다.
- { key: fuel_percent, preset: fuel_level, update_interval: 30s }
# 연료량은 이 차에서 읽을 방법이 없다. 표준 01 2F는 실차에서 NO DATA를
# 돌려주고(OBDb 캡처는 북미 가솔린 기준이라 디젤에는 맞지 않았다),
# 계기판 22B002도 7F 22 22로 거부한다.
# awesomeit 엑센트RB 2013 D 1.6 TCI-U2 프로필에서 확인된 값들
- key: intake_temp
mode: "21"
@@ -229,25 +229,37 @@ templates:
#
# 응답이 byte 57까지 도착하지 않으면 decode가 null을 돌려주고 아무것도
# 발행되지 않는다 — 미지원 차에서 엉뚱한 값이 올라오지 않는다.
#
# offset_value = -1436.5 는 계기판 대조 보정이다. 2026-07-30 실측에서
# ECU 카운터 197394.5 km, 계기판 195958 km 로 0.733% 높게 나왔다.
# 이 카운터는 DPF 서비스 주기용이라 법정 계기판 수치와 별개로 관리되고,
# 속도 신호원이 달라 장기간에 걸쳐 벌어진다.
# 측정이 한 번뿐이라 상수 오차인지 비례 오차인지 구분되지 않아 우선 상수로 뒀다.
# 100km 이상 주행 후 재확인할 것:
# 차이가 1436.5 그대로면 상수가 맞고, 1437.2 근처로 늘면 비례이므로
# offset_value 를 빼고 scale 을 0.000992723 으로 바꾼다.
- key: odometer
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.001 }
decode: { offset: 57, length: 4, type: uint32, endian: big, scale: 0.001, offset_value: -1436.5 }
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 1
icon: mdi:counter
update_interval: 60s
# 검산용. 재생시점 주행거리 + 재생후 거리 = 총주행거리가 성립해야 한다.
# 검산용: 재생시점 주행거리 + 재생후 거리 = 총주행거리.
# 재생시점 값도 같은 ECU 카운터라 위와 같은 보정을 걸어야 이 관계가 유지된다.
# 재생후 거리는 차분이라 편향이 없으므로 보정하지 않는다.
- key: odometer_at_last_dpf_regen
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.001 }
decode: { offset: 49, length: 4, type: uint32, endian: big, scale: 0.001, offset_value: -1436.5 }
unit: "km"
device_class: distance
state_class: total_increasing
accuracy_decimals: 1
entity_category: diagnostic
update_interval: 60s
@@ -258,17 +270,10 @@ templates:
decode: { offset: 53, length: 4, type: uint32, endian: big, scale: 0.001 }
unit: "km"
device_class: distance
state_class: measurement
accuracy_decimals: 1
entity_category: diagnostic
update_interval: 60s
# raw= hex를 로그에 남기기 위한 프로브. 위 센서들이 값을 내면 지워도 된다.
- key: probe_2103
mode: "21"
pid: "03"
pre_commands: ["ATSH7E0"]
formula: "a"
entity_category: diagnostic
update_interval: 60s
- id: gatt_meter_relay
name: "GATT power meter + relay"